Confirm that the router image is installed.
ICX6610-24 Switch#show flash Stack unit 1: Compressed Pri Code size = 5320842, Version:07.3.00aT7f1 (/foundry/FGS/os/FCXS07300a.bin) Compressed Sec Code size = 6803305, Version:07.3.00aT7f3 (/foundry/FGS/os/FCXR07300a.bin) Compressed Boot-Monitor Image size = 369491, Version:07.3.01T7f5 Code Flash Free Space = 52822016 Configure the switch to reboot from the secondary image. ICX6610-24 Switch#boot system flash sec secondary From Secondary image flash ICX6610-24 Switch#boot system flash secondary Are you sure? (enter 'y' or 'n'): y Halt and reboot Rebooting(2)... * $ ICX Boot Code Version 7.3.01 (grz07301) Enter 'a' to stop at memory test Enter 'b' to stop at boot monitor BOOT INFO: load monitor from boot flash, cksum = b4d2 BOOT INFO: verify flash files......... BOOT INFO: load image from secondary copy... platform type = 8 PCIE-1 LTSSM status: 22 PCIE Switch status: 0 ..................... ..... Starting Main Task ...CPSS DxCh Version: cpss3.4 release Pre Parsing Config Data ... Parsing Config Data ... Copyright (c) 1996-2011 Brocade Communications Systems, Inc. UNIT 1: compiled on Dec 02 2011 at 11:46:03 labeled as FCXR07300a (6803305 bytes) from Secondary /foundry/FGS/os/FCXR07300a.bin SW: Version 07.3.00aT7f3 Boot-Monitor Image size = 369491, Version:07.3.01T7f5 (grz07301)
HW: Stackable ICX6610-24
UNIT 1: SL 1: ICX6610-24 24-port Management Module Serial #: BXP2551H0BX License: ICX6610_BASE_ROUTER_SOFT_PACKAGE (LID: dzrHKKGjFdz) P-ENGINE 0: type E02B, rev 01 UNIT 1: SL 2: ICX6610-QSFP 10-port 160G Module UNIT 1: SL 3: ICX6610-8-port Dual Mode(SFP/SFP+) Module 800 MHz Power PC processor 8544E (version 0021/0023) 400 MHz bus 65536 KB flash memory 512 MB DRAM STACKID 1 system uptime is 9 seconds The system : started=warm start reloaded=by "reload" ........................ ICX6610-24 Router> Power supply 2 detected. Power supply 2 is up. ICX6610-24 Router>en No password has been assigned yet... ICX6610-24 Router#
Note that the hostname has now changed to ICX6610-24 Router
CyberSecFaith 
Wow, superb blog layout! How long have you been blogging for?
you make blogging look easy. The overall look of your web site is fantastic, let alone the content!
LikeLike
Thank you.
LikeLike
Is this boot supposed to be permanent? I edit and write mem, but when I reload the switch I boot back to primary flash code not the secondary.
LikeLike
add ‘boot system flash sec’ to your config. be sure to ‘wr mem’
LikeLike
Thanks for helping out Brad.
LikeLike
add ‘boot sys fl sec’ to your global config. be sure to ‘wr mem’
LikeLike
The last Line: “Note that the hostname has not changed to ICX6610-24 Router”
should this read “Note that the hostname has now changed to ICX6610-24 Router” ?
(not changed to now)
LikeLike
Thanks Brian. I have updated that now.
LikeLike